BES384EB2 Crosley Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from FOREST HILLS, KY
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would start to heat then quit,checked the temperature sensor with ohm meter after cool down reading about 1100 ohms. I cleaned connection tried it again seemed to work well but quit again in just few days.
Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great
OEM parts plug in same, works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Coeur d'Alene, ID
- Parts Used:
- 318228310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lens was broken
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oscar from Scranton, KS
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
F10 Error. Temp sensor at 1189 room temp ohms
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glyndon from BOWLING GREEN, KY
- Parts Used:
- 318254906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Bake element burnt out
Tool old elentment out, put new element in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from MORGANTON, NC
- Parts Used:
- 318198817
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element not working
Open range door remove 2 screws on bottom of stove top remove top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willis from Friendsville, TN
- Parts Used:
- 5304467898
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Convection fan making noise
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!