Models > ACO27DK-P1132334NK > Instructions

ACO27DK-P1132334NK Amana Wall Oven - Instructions

Jump to:

All Instructions for the ACO27DK-P1132334NK
16 - 30 of 33
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Cheryl from Tallahassee, FL
Parts Used:
WP77001092
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The oven wouldn't bake anymore.
First I removed the two screws that held the element in place. Then after slightly pulling out the wires, I disconnected the two wires on each side. The new part just snapped into the old wires. I pushed the element back into place, replaced the original two screws to hold it into place, and it was all done! Two screws and two wires...done. It took about 2 minutes and this is something I have NEVER done before. The oven works beautifully now!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ivanka from Atlantra, GA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherrie from Orange, TX
Parts Used:
WP77001092
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bottom element wouldn't heat
Turned off the breaker. Unscrewed the two srews holding the element in the back of the oven. Pulled out old element. removed the clips from the old element, placed them on the new one. Pushed the element into place. replaced the screws. Turned on the breaker. Total time about 5-6 minutes. Wish all reapirs were this simple and easy.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from Paradise, CA
Parts Used:
WP77001092
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Lower element not heating
I was astounded, I ordered the part on Thursday afternoon and FedEx delivered it on Saturday afternoon. Great overall service.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry from Sharpsburg, GA
Parts Used:
WP77001092
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
Bake Element burned out after 24 years of lot's of use
The key was finding the right socket and using my 1/4 inch socet set and rachet. Remove your nuts, pull out disconnect wires, remove old element and put new one in place. One tip is turn on stove light to be able to see well while in oven.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from Ada, MI
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Phoenix, AZ
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RAYMOND from JACKSONVILLE, FL
Parts Used:
4396923
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broiler pan missing
ordered new broiler pan
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peggy ann from forest city, NC
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced oven lightbulb
very easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shirley from Las Vegas, NV
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lisa from Knoxville, TN
Parts Used:
WP77001092
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Slow heating oven
To diagnose the problem I felt of the element a few moments after turning the oven on. It was cold. (rocket science, I know). I ordered the element replacement, which arrived less than 24 hours later. I turned off the power to the oven, unscrewed the old element and pulled. The wires are attached to the element in a way that reminds me of plugging in a USB port. Plugged, screwed back in, powered up and made some banana bread.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Willliam from Goldfield, IA
Parts Used:
WPY0314907
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
gears and gear box top case cracked
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!
Was this instruction helpful to you?
Thank you for voting!
Customer:
thomas from iron mountain, MI
Parts Used:
Y0309305
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
control panel was burnt out
Unscrewed the oven from the opening. Removed the metal housing on the oven. Found the control panel. Hard to remove with the type of plastic anchors holding the panel on. Wasn't bad after that. Just had to keep track of the wires as you disconnected them. Reconnect to new board as you disconnect was the simplest. Worked just fine after that. nice new oven again.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wesley from Norman, OK
Parts Used:
WPY0314907
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Oven not heating, F3 trouble code.
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ACO27DK-P1132334NK
16 - 30 of 33