Models
>
FX26SCE
FX26SCE (Type 2) Weed Eater Trimmer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FX26SCE
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
$9.32
This is a single fuel filter found in numerous types of lawn and garden equipment that have small engines. The fuel filter cleans the fuel before making its way to the carburetor, thus preventing buil...
In Stock
Order now and your part arrives by Apr 6
$12.41
The 530014347 Fuel Cap Assembly is a genuine Poulan replacement part. It purpose is to keep the fuel in the fuel tank. It is removed from the fuel tank to refill the tank. It includes a retainer that ...
In Stock
Order now and your part arrives by Apr 6
$24.13
This genuine fuel tank assembly is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman trimmers and weedwackers. Made from high-quality plastic for du...
Special Order
$8.32
Genuine Weed Eater replacement part, this item is sold individually. The 530058000 Trigger is inside the handle of the trimmers shown below. It connects to the throttle cable which controls the speed ...
Special Order
$7.77
This is an Original Manufacturer Approved replacement part. This part is made out of Foam and it is sold individually. The purpose of the filter is to keep dust and debris from contaminating the carbu...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams f...
In Stock
Order now and your part arrives by Apr 6
This is a genuine OEM approved replacement component which is specially designed for use with Craftsman handheld lawn and garden equipment. The purpose of this spring is to retract the starter assembl...
No Longer Available
$2.99
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers. The metal retainer is used to secure the spool withing the cutting head h...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is an authentic OEM sourced replacement piston ring used on gas Trimmers and blowers. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase, causing...
In Stock
Order now and your part arrives by Apr 6
Genuine OEM replacement part, this part is sold individually. The purpose of the 530053241 Return Spring is to push the bump knob of the spool assembly back into its original position after you have b...
No Longer Available
$14.35
This is a Manufacturer Approved replacement kit used on a variety of Gas Trimmers/Pruners. This gasket set includes the major gaskets to replace when rebuilding the engine. Its purpose is to make an a...
Special Order
$59.00
Genuine OEM replacement part, this part is sold individually. A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the for...
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FX26SCE
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Engine stops after a few seconds or minutes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rosanne from BRIDGEWATER, VA
- Parts Used:
- 545227901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Clogged muffler
Remove the 4 screws holding the rear motor casing. Then you can take the easy route and drill through the front motor housing with a 3/8 to 1/2 bit in order to access the front muffler screw. If you want to work harder you must remove the motor from the shaft, remove the clutch assembly (this requires a long 15t torx bit, removing the spa
... Read more
rk plug to stuff the piston with rope or rag to seize up the piston, and then removing the front motor casing to access the front muffler screw). Once you access both muffler screws remove them with the t20 torx driver. Install the new muffler with the small gasket inside the housing, and the larger gasket/heat shield between the muffler and the motor.
Read less
Was this instruction helpful to you?
Thank you for voting!