Models > RY28120

RY28120 Ryobi Trimmer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for RY28120

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This is a spool retainer for your trimmer. You may also know this part as a bump knob. It is a right-hand thread screw to remove and attach to your trimmer head. Inside the spool housing, it holds the...
No Longer Available
This spring or container fits gardening tools such as a trimmer. The spring works to recoil a starter rope. If your spring has been worn out, it can lose tension and even break. If the spring breaks, ...
In Stock
Order now and your part arrives by Mar 22
This is a genuine OEM replacement part, it is sold individually. The purpose of the 901552001 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to...
In Stock
Order now and your part arrives by Mar 22
This is a grass deflector assembly for a trimmer. Your model may have a straight deflector and a curved shaft deflector, and this one is considered the curved shaft deflector. Its purpose is to help p...
No Longer Available
This Genuine OEM replacement part is sold individually. It includes the fuel lines, fuel cap 308680001, and fuel filter 308675051. The 308675051 Fuel Tank is a commonly used part in trimmers and other...
No Longer Available
Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat i...
In Stock
Order now and your part arrives by Mar 22
This is an OEM Manufacturer Sourced replacement part used on certain Gas Powered String Trimmers. This part is made out of Foam and it is Sold Individually. Its purpose is to filter out dust and debri...
In Stock
Order now and your part arrives by Mar 22
This is a genuine OEM approved replacement part designed for use with a variety of handheld lawn and garden equipment. This is an in-tank fuel filter which makes sure that the fuel delivered to the en...
In Stock
Order now and your part arrives by Mar 22
Genuine OEM replacement part used on some models of Gas String Trimmers. This part is made out of Plastic with included Metal Eyelet. This part holds and secures the Spool. Please note: Spool, Spring ...
No Longer Available
This is a Genuine OEM sourced replacement part designed for use with Ryobi String Trimmers and Brushcutters. This item is made out of Metal and it is Sold Individually. It is the Lower Shaft that the ...
No Longer Available
$6.70
This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driv...
In Stock
Order now and your part arrives by Mar 22
This is a genuine OEM sourced replacement part that is intended to be used with trimmers and pruners from Homelite and Ryobi. The metal screw is commonly used to fasten the muffler assembly to the cyl...
No Longer Available

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Irvin from BURR OAK, MI
Parts Used:
308038010
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
bearing set up in lower shaft.
Purchased and replaced curved lower shaft assembly.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JAE from MILL HALL, PA
Parts Used:
308038010
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
THE DRIVE SPLINE IN THE MIDDLE OF THE SHAFT WOULD NOT ENGAGE
REPLACED LOWER SHAFT
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!