Models
>
41BD25SC900
41BD25SC900 MTD Trimmer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$45.02
A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, ...
In Stock
Order now and your part arrives by Aug 10
$18.38
This bump knob assembly fits lawn and gardening tools, usually trimmers. This part bumps on the ground to advance the cutting line from the spool. With time and use, this part can wear out easily. It ...
In Stock
Order now and your part arrives by Aug 10
$10.83
This is a genuine OEM replacement throttle trigger (red). The throttle trigger is responsible for managing the speed of the engine. The throttle cable attaches to the trigger, which connects to the th...
On Order
$18.85
This is an authentically sourced fuel tank assembly, including the fuel lines, fuel cap, fuel filter, and screws needed for assembly. This fuel tank assembly is for trimmers, and is where the fuel is ...
In Stock
Order now and your part arrives by Aug 10
$28.55
This spool is for line trimmers.
Spool houses the cutting line and fits inside the cutting head to cut grass and weeds.
Wear work gloves to protect your hands when installing this part.
In Stock
Order now and your part arrives by Aug 10
$15.64
Genuine OEM replacement part, this item is sold individually. This spring is used on all of the trimmers listed below. It is installed between the inner reel and the outer spool assembly. Its purpose...
In Stock
Order now and your part arrives by Aug 10
$6.51
This is a genuine OEM replacement part designed for use with some Handheld String Trimmers. This filter is made out of Foam and it is sold individually. The purpose of this filter is to keep dirt and ...
In Stock
Order now and your part arrives by Aug 10
$6.51
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carbure...
In Stock
Order now and your part arrives by Aug 10
$6.51
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburet...
In Stock
Order now and your part arrives by Aug 10
This is a Manufacturer Approved replacement part designed for Gas String Trimmers. The purpose of this Cover is to secure Foam Filter which is Sold Individually and protect internal parts like Carbure...
Special Order
$11.58
This is a genuine manufacturer approved replacement mulching door torsion spring designed for use with handheld trimmers/edgers. This spring helps the throttle trigger to retract. It is made out of me...
On Order
$27.55
This is an OEM sourced replacement part used on Gas Trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driv...
In Stock
Order now and your part arrives by Aug 10
Common Problems and Symptoms for 41BD25SC900
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Engine stops after a few seconds or minutes
Fixed by these parts
How to fix it
Cutting line does not come out
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erik from ROBERTSDALE, AL
- Parts Used:
- 753-06183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fuel line broke
Removed the two screws holding the fuel tank to the main unit. Removed the two fuel lines and any stuck on rubber. Installed and installed two screws to mount the new tank. Slid fuel lines on their respective connectors. Done.
Was this instruction helpful to you?
Thank you for voting!
string trimmer would not start
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines o
... Read more
nto the new carburetor.put some fuel in the tank. started the trimmer. runs great.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CV from Shasta Lake, CA
- Parts Used:
- 753-06330
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken lower drive shaft cable (engine runs fine, trimmer string head doesn't spin).
Remove lower shaft housing alignment set screw, and bolt clamp that connects the lower and upper drive shaft housing. Then remove the 6 star head screws that hold split housing for the drive gears, and carefully split and separate the housing. Remove the broken drive shaft cable. Grease the replacement drive shaft cable full length (ver
... Read more
y important), and re-grease the drive gears before reassembly. Very quick and easy repair. Just be sure to grease the cable heavily full length, and the coupler that connects the upper and lower cables.
Read less
Was this instruction helpful to you?
Thank you for voting!