Models
>
358791042
358791042 Craftsman Trimmer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 358791042
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
In Stock
Special Order
In Stock
Special Order
This is a single fuel filter found in numerous types of lawn and garden equipment that have small engines. The fuel filter cleans the fuel before making its way to the carburetor, thus preventing buil...
No Longer Available
If your fuel line has become brittle and started to crack, this is the replacement part you will need. This OEM fuel line, also known as a tank purge line, is made from a flexible translucent rubber a...
No Longer Available
In Stock
This is a fuel line for your lawn equipment. The line connects your fuel tank and carburetor. It delivers gas to the carburetor when needed. This part is made of clear, flexible rubber, and is 25 inch...
No Longer Available
On Order
This part includes one primer bulb, also known as a purge bulb. This high-quality replacement part is sourced right from the original manufacturer. When the engine of your equipment has been left unus...
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
May 12, 2022
How do you install new pull cord
For model number 358791042
Hello Bill, thank you for your question. Please see the following steps to install cord. Remove the end cover. Remove the snap ring. Disassemble the unit into two pieces. Remove the coil from the shaft. Hold the spring in place after removing the coil. Remove the broken piece of rope. Clean out debris on the cover. Measure out a new piece of rope. Thread the new rope into the coil assembly. Tie a small knot at the end of the rope and pull it into the coil pocket. Wind the pull cord rope around the coil. Reinstall the coil into the housing. Turn the coil two revolutions clockwise to add tension.
Thread the rope through the hole in the end cover. Install the handle. Reinstall the end cover. We hope this helps.
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for 358791042
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
installing fuel through fuel tank wall
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t
... Read more
hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Read less
Was this instruction helpful to you?
Thank you for voting!