TC800SPHB0 Whirlpool Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Greene, RI
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
It is held on with three screws. The PartSelect was the only web site that showed me a picture of the part I wanted. The other web sites said it was no longer made. It was shipped out the day I ordered it, and took a minute to install it. Will order again from your company - great service - thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindie from DUNMORE, PA
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable), Wrench set
Front legs were rotted.
Replace front legs. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from LUTHER, OK
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Compactor won't stop
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DELAWARE, OH
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEWBERRY, MI
- Parts Used:
- WP9871602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Rollers wore out
Removed and replaced in less than 15 minutes. Works like new again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from DENNIS, MA
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had a newly cracked handle on a 36 year old trash compactor.
Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ROSWELL, NM
- Parts Used:
- 882688
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
One of the roller wheels was worn out
Removed drawer
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid back into cabinet
inserted drawer
tested
Works as good as new
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid back into cabinet
inserted drawer
tested
Works as good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from JEFFERSON CTY, MO
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The previous handle broken in half.
There were two screws holding the handle on, We removed the two screws, removed the broken handle and screwed the new handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathrine R from OKLAHOMA CITY, OK
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!
So glad you had the part. It was pricey, but way less than a new trash compactor!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from SPRING GROVE, IL
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer handle
Removed two screws on back of pull out door. Pulled up on handle, came out easily, slide the new one in, replaced the screws and done. Less than 5 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Gilroy, CA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Jammed KitchenAid Trash Compactor.
With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.
I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.
I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.
I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.
I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elbert from FRANKLIN, OH
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ram would not go up and down gears went bad
layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Flagstaff, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Compactor would not open. Ram was down
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kelton from weatherford, TX
- Parts Used:
- WP9870163
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
One of the nuts on the ram stripped out
1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but is vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.
Was this instruction helpful to you?
Thank you for voting!