GX900QPPB1 Whirlpool Trash Compactor - Instructions

There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

removed old parts and replaced

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Removed bottom and replaced gears

After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

I had no problem. My husband is an engineer, so the repairs went well. The only problem I did have was that one of the parts did not arrive. come to find out that it was on backorder and arrived a day or two after I called. The person I spoke with when I inquired was most helpful and expeditious. All in all, my experience was excellent.

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

removed old handle by removing screws - installed new handle by inserting screws in same in same location as those removed

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

A trash compactor is a very simple machine. Basically there are two parts that could cause the problem of the machine not shutting off at the end of the cycle. The limit switch which was listed as the most likely cause and the momentary contact switch, if fused would cause the same problem. I first replaced the limit switch and to my dismay, the problem continued which meant the contact switch was at fault. The switch unit is easy to get too, First remove the two screws securing the front panel to the machine. Then transfer the wires from the old switch to the new. Remove two screws which secure the switch unit to the front and discard the old switch. Reassemble the unit in the reverse order and plug the unit back into the wall. Works perfectly!