TC8750XYP1 Whirlpool Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Willow Creek, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Primary Power Transfer Gear Split in Half
Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partselect part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tena from Parker, CO
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
compactor wouldn't compact
bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Quincy, IL
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
the compactor was stuck in the down position
Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from San Rafael, CA
- Parts Used:
- WPW10242557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I changed the front panels from the original beige to stainless steel
The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Columbus, NE
- Parts Used:
- W10856868
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Off/On/Start button was wore out
Two screws to take panel off, two screws to take off button array, unplug 4 wires, put the new one in, reverse the process, worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from lincoln, AR
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stripped pinion gear
I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myles from Jackson, NH
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
compactor was crushing the bag holder
easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Belmont, NH
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
20+ plactic gears striped them selfs who da thunk
took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from ODESSA, TX
- Parts Used:
- 777941
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
minor replacement
Removed panel and replaced it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Elk Creek, CA
- Parts Used:
- WP9870444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The panel got bent
Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!
Was this instruction helpful to you?
Thank you for voting!