TU8100XTP0 Whirlpool Trash Compactor - Instructions

replaced power nuts

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

The part that doews the actual compacting would not move correctly. The machine would not stop because the part never contacted the spring loaded switch. I had known about this for about a year, but put it off until it stopped working altogether. I ordered 2 power nuts and rec'd them in B.F.E. Alaska in about 5 days. I quickly replaced the parts and the machine works like brand new again. I estimate this compactor to be at least 10 -15 years old and replacing the occassional part once in awhile is a lot cheaper than buying a new compactor.

refloored the floor and so the unit would not come out. had to cut tile, broke edge off of formica counter but once the unit was out a piece of cake. 6 self tapping screws removed , right on the top, two screws holding the cover for the power nuts, replaced broken nut, leveled ram, replaced nuts and ready to slide back in. After thought, I had one nut on hand from a few years earlier. I ordered two new nuts and now i am going to pull the unit again and replace both nuts. thought being a longer period before having to do this again. The unit was put in in 1981 and used continuously.

changed out the big gear that was broken

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

Ordered three parts, however if I had read your repair page more thoroughly I could have avoided buying the top of cycle off switch. Oh well... This thirty year old trash compactor is back in business running like a new one. My one recommendation? READ YOUR FAQ PAGE. It will save you money.dan

Ordered part and received it in two days. Unplugged the compactor from wall outlet. Removed two screws holding control panel in place, marked proper wire location on rear of panel, disconnected push-on terminations from start/run switch. Removed knurled nut holding start/run switch onto the control panel and substituted the new switch. Reassenbled everything in reverse order to disassembly and plugged power cord back into the wall outlet. No further work required.

Used visuals from partselect web site to dismantle the trash compactor , remove broken power nut , order new nuts. Only took a few days to receive new nuts. Replaced nuts , put back together and now works fine.