TU800SPKQ0 Whirlpool Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from CLARKSTON, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mona from San Diego, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
ram wouldn't go up or down.
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Houston, TX
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Compactor piston stuck in down position and couldn't open!!!
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ALICE, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bad gears and a bad switch
Put the parts in and reinstalled it back in it place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- WP9871602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
Roller was flat
Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ASHEVILLE, NC
- Parts Used:
- 882688
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southington, CT
- Parts Used:
- 780334
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dented front panel
The first panel I received was scratched and had to be replaced. I called PartsSelect and they sent a replacement.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DELAWARE, OH
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Flagstaff, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Compactor would not open. Ram was down
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmen M from Port Orchard, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Trash carier wore out
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from MUNCIE, IN
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEWBERRY, MI
- Parts Used:
- WP9871602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Rollers wore out
Removed and replaced in less than 15 minutes. Works like new again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAN DIEGO, CA
- Parts Used:
- WP9871267
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle to compactor cracked and broken
Super easy - removed the TOP three screws from behind the door. Wiggled the handle out pulling upwards. Slid the new handle in and screwed it back into place. More importantly I had my part the very next day - AWESOME. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Choy from APPLE VALLEY, MN
- Parts Used:
- WP9871267
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
2 of 3 crew connectors on old handle broke off, making pulling action of opening compactor wobbly, loose.
1. Loosen screws to remove old handle. 2. Insert new handle into position, align holes on steel backing with connectors on back of handle. 3. Screw on 3 screws, beginning with middle, then left & right. 4. Tighten to firmness. 5. Close & open to test for installation compketeness.
Was this instruction helpful to you?
Thank you for voting!