TU800SPHB0 Whirlpool Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Adrien from East Freetown, MA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Pushed button, made a buzzing noise, nothing happened.
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clem from Scottsdale, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
motor gear broken
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reagan from Glenshaw, PA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Plastic Gear Wheel Broke
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from KERRVILLE, TX
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
ram would stop where ever you let go of switch
replaced rotatory switch (10mins) problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from Granada Hills, CA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ram quit moving
Removed bottom and replaced gears
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from South Boston, MA
- Parts Used:
- 882699
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Compactor ram was stuck in the down position and door would not open
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Huntingdon Valley, PA
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle had cracked
So impressed with this Company. Was about to buy new trash compactor, because we couldn't find a handle for an old Frigidair. Found website and on Friday ordered part (only $57...a new compactor would have cost $800). Part arrived ONE DAY LATER and was immediately easily installed by taking out old part which involved unscrewing it and installing the new one using the existing screws. THANK YOU.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Painted Post, NY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Drive Gear
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from GRANADA HILLS, CA
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle Broken
Simply slid handle into door compartment at top, and put in the 2 screws to hold it in place. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
roller bearing for trash bin was damaged and would not allow canister to roll
the bearing were the perfect match and instructions helpful. sysem is rolling smoothly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Wickenburg, AZ
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Unit cycled when on switch operated and would not stop until Off switch was activated.
Replaced the limit switch. This did not alter the problem. Took off the On/Off/Start switch and dissasembled. I found the the Start switch was stuck in the on position. I reassembled the switch mechanism assuring that the Red "ON" indicator moldings were correctly positioned and reassembled everything. The Compactor now works properly. Need to add "Check the Start switch" to diagnosis.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from San Rafael, CA
- Parts Used:
- WP777328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I changed the front panels from the original beige to stainless steel
The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from DENNISPORT, MA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken drive gears
Took out old gears replaced with new very easy with your dirictions.
Was this instruction helpful to you?
Thank you for voting!