KUCS02FRPA0 KitchenAid Trash Compactor - Instructions

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.

This replacement kit did solve the problem but required replacement of a number of parts because the switch and actuator functionality had been redesigned. Fitting the kit of parts requires that you have to slide the compactor away and out of its location (might be a bit tricky if it's beautifully integrated into a designer kitchen)so as to remove the front cover. Some heavy leather gloves could be helpful here since there are several sharp edges on the pressed steel carcase of the unit. Once free the kit replacement is relatively easy (for the average handyman/woman), following the simple instructions provided. You will need to drill two new holes in the front plate (template provided) so an electric drill and a sharp drill bit (for metal) will be needed. Most important - the kit worked; and with a more reliable component than that replaced.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

It was an updated revision part kit...and it went so smooth ....recommend that anyone looking to repair appliances utilize PartSelect....I know I will be ...Thank You

Went well but took time. Instructions adequate but not detailed.

replaced the large gear and put it back together.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

The instructions were pretty straight forward. I did not expect to receive the foot pedal and switch as mine was still ok. However, I find that everything works with less effort than before. I did have to trim the new toe guard as it hit the actuator button when opening and closing the compactor.

After removing the compactor from under the counter, and unplugging it, I did the disassembly. The replacement parts were easy to install. Two holes had to be drilled to mount the switch, but that was not difficult. Overall, the instructions were easy to follow and the parts all fit.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screws from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

changed out the big gear that was broken

Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partselect part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.