KCCC151EWH1 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- james from Milton, MA
- Parts Used:
- WPW10451276
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The compactor was loaded with too many wine bottles
At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behind the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from San Rafael, CA
- Parts Used:
- WPW10242557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I changed the front panels from the original beige to stainless steel
The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from lincoln, AR
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stripped pinion gear
I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheila from helendale, CA
- Parts Used:
- WP9871267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
replaced with new that arrived very quickly I am very happy since I put it off a long time. If I new how easy I would have done it 3 yrs ago. Thanks, Sheila
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Taylors, SC
- Parts Used:
- WP9871267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
Hey real easy, remove old handle and replaced with new one. had to drill holes for the ends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from CASPER, WY
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
compactor will not stop when compaction complete on top cycle
take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janie from mcHenry, IL
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the switch did not click off
very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Belmont, NH
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
20+ plactic gears striped them selfs who da thunk
took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from San Antonio, TX
- Parts Used:
- WP9871267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The plastic handle on the compactor was broken
Removed the three screws holding the broken handle to the compactor and used them to attach the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myles from Jackson, NH
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
compactor was crushing the bag holder
easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Elk Creek, CA
- Parts Used:
- WP9870444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The panel got bent
Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Jacksonville, FL
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drive motor would not turn off after completing cycle
Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Goshen, KY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken plastic drive gear
Very simple, changed the gear, adjusted the drive and tested. Very straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Campbell, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Large plastic gear cracked in half. Compactor was stuck in the compact postition
replaced the large gear and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from DENNISPORT, MA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken drive gears
Took out old gears replaced with new very easy with your dirictions.
Was this instruction helpful to you?
Thank you for voting!