KFCK03ITWH0 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Goshen, KY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken plastic drive gear
Very simple, changed the gear, adjusted the drive and tested. Very straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from DENNISPORT, MA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken drive gears
Took out old gears replaced with new very easy with your dirictions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Campbell, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Large plastic gear cracked in half. Compactor was stuck in the compact postition
replaced the large gear and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from WAYLAND, MI
- Parts Used:
- 882699
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
plastic gear broke in half
Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from CASPER, WY
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
compactor will not stop when compaction complete on top cycle
take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Taylors, SC
- Parts Used:
- WP9871267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
Hey real easy, remove old handle and replaced with new one. had to drill holes for the ends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from San Antonio, TX
- Parts Used:
- WP9871267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The plastic handle on the compactor was broken
Removed the three screws holding the broken handle to the compactor and used them to attach the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Milton, MA
- Parts Used:
- WPW10451276
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The compactor was loaded with too many wine bottles
At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behind the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Quincy, IL
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
the compactor was stuck in the down position
Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph N from Wheaton, IL
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ram was stuck in the down position
changed out the big gear that was broken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candace from Ocala, FL
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Ram stuck in down poaition
Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dick from Penn Valley, CA
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Directional Switch lever broke
The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.
Was this instruction helpful to you?
Thank you for voting!