KUCV02FRMT0 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Clayton, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Compactor wouldn't function. We found a small piece of metal on the floor that turned out to be a part of the switch actuator
repair was simple. just removed the two screws that were holding the rest of the switch actuator in place and installed the new one in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from LUTHER, OK
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Compactor won't stop
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kelton from weatherford, TX
- Parts Used:
- WP9870163
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
One of the nuts on the ram stripped out
1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but is vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clem from Scottsdale, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
motor gear broken
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from glendale, AZ
- Parts Used:
- W10165295RP, 13030RP, W10540354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
unit was missing parts
Installed new parts. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Westlake Village, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The actuator had broken off, causing the foot lever to be inoperative.
The repair is quite simple. All you have to do is attach the new actuator using the screws provided. The only question that arose came from the actuator part being delivered with two rubber gromets that are not used in the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Poway, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
took off old piece, screwed on new one. works fine.
straight blade screwdriver. easy as pie.
many thanks
many thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reagan from Glenshaw, PA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Plastic Gear Wheel Broke
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Painted Post, NY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Drive Gear
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E Arlene from Reno, NV
- Parts Used:
- WP9871920
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part was missing
plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from South Boston, MA
- Parts Used:
- 882699
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Compactor ram was stuck in the down position and door would not open
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from Granada Hills, CA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ram quit moving
Removed bottom and replaced gears
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Edmond, OK
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch broke off and would not activate compactor
removed two screws and replaced broken piece. Only thing a little difficult was getting screws in tightly enough to hold piece secure.
Was this instruction helpful to you?
Thank you for voting!