KUCC151DBL0 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith V from Studio City, CA
- Parts Used:
- WPW10242557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The compactor rubber guard was torn.
Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Dallas, GA
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
compactor wouldn't shut off
changed out the switch and that fixed the problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Houston, TX
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Compactor piston stuck in down position and couldn't open!!!
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DELAWARE, OH
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mona from San Diego, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
ram wouldn't go up or down.
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- WP9871602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
Roller was flat
Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ASHEVILLE, NC
- Parts Used:
- 882688
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ALICE, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bad gears and a bad switch
Put the parts in and reinstalled it back in it place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elbert from FRANKLIN, OH
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ram would not go up and down gears went bad
layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southington, CT
- Parts Used:
- 780334
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dented front panel
The first panel I received was scratched and had to be replaced. I called PartsSelect and they sent a replacement.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fairview, NC
- Parts Used:
- WP9872161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Compactor ram would not automatically return to starting position
Removed two screws holding front panel.
Disconnected three wires to rocker switch noting position.(each wire is a different color and is an insulated blade connector. Pull off...push back on.
Compressed barbs holding old switch in place and removed switch.
Pressed in new switch until it popped into locked position. Reconnected wires.
Reattached front panel.
Disconnected three wires to rocker switch noting position.(each wire is a different color and is an insulated blade connector. Pull off...push back on.
Compressed barbs holding old switch in place and removed switch.
Pressed in new switch until it popped into locked position. Reconnected wires.
Reattached front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from CLARKSTON, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LAWRENCEBURG, IN
- Parts Used:
- WP9871031
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Compactor was hard to open had to press hard with foot and lift to open. got harder as it got fuller.
remove the container from base lay on floor unscrew 2 screws one on each side and remove foot pedal. I could see that the foot pedal had small bow in the pedal. You can only see this if you removed. I ordered the rollers in the front but did not install as it is not the rollers. Will keep for future if needed. Replace your foot first if hard to open.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SANDPOINT, ID
- Parts Used:
- WP9872161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rocker switch was not operating properly
Took the 2 screws off the front, popped the switch out, copied the wires on to the new switch, and put it back. New switch does not have a light, so had to eleminate one power wire, put it back together, and it worked just like new.??
Was this instruction helpful to you?
Thank you for voting!