KUCC151EAL0 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Choy from APPLE VALLEY, MN
- Parts Used:
- WP9871267
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
2 of 3 crew connectors on old handle broke off, making pulling action of opening compactor wobbly, loose.
1. Loosen screws to remove old handle. 2. Insert new handle into position, align holes on steel backing with connectors on back of handle. 3. Screw on 3 screws, beginning with middle, then left & right. 4. Tighten to firmness. 5. Close & open to test for installation compketeness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from WEST HILLS, CA
- Parts Used:
- WP9871267
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
changed broken trash compactor handle
Unscrew and remove old handle and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from DANVILLE, CA
- Parts Used:
- WP9871099
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
CLIPS BROKEN OFF PART WOULD NOT STAY IN PLACE
PUT FILTER IN PLACE AND SNAPPED IN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEWBERRY, MI
- Parts Used:
- WP9871602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Rollers wore out
Removed and replaced in less than 15 minutes. Works like new again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAN DIEGO, CA
- Parts Used:
- WP9871267
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle to compactor cracked and broken
Super easy - removed the TOP three screws from behind the door. Wiggled the handle out pulling upwards. Slid the new handle in and screwed it back into place. More importantly I had my part the very next day - AWESOME. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kelton from weatherford, TX
- Parts Used:
- WP9870163
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
One of the nuts on the ram stripped out
1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but is vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from LUTHER, OK
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Compactor won't stop
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrien from East Freetown, MA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Pushed button, made a buzzing noise, nothing happened.
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from glendale, AZ
- Parts Used:
- W10165295RP, 13030RP, W10540354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
unit was missing parts
Installed new parts. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reagan from Glenshaw, PA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Plastic Gear Wheel Broke
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clem from Scottsdale, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
motor gear broken
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from KERRVILLE, TX
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
ram would stop where ever you let go of switch
replaced rotatory switch (10mins) problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from Granada Hills, CA
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ram quit moving
Removed bottom and replaced gears
Was this instruction helpful to you?
Thank you for voting!