4KUCC150S2 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from DELAWARE, OH
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from TACOMA, WA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Trash Compactor ram will not move while motor running, stripped power nuts
Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearing cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from CLARKSTON, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southington, CT
- Parts Used:
- 780334
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dented front panel
The first panel I received was scratched and had to be replaced. I called PartsSelect and they sent a replacement.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmen M from Port Orchard, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Trash carier wore out
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from MUNCIE, IN
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sequim, WA
- Parts Used:
- WP4314961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
LIght switch on oven door was broken
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Flagstaff, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Compactor would not open. Ram was down
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from salinas, CA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
Trash Compactor didn't work
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheila from PINE BLUFF, AR
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
compactor would not compact the trash
took appliance out of cabinet, found the problem to be two nuts on the big screw bars that drive the compaction machine up and down. These things were wore out. We replaced them and turn the electricity back on and tried the compactor and it worked perfect. Of course here was to top cover that had to be removed and reinstalled . all in all it wasn't to difficult. A new machine cost 1100 dollars. This old one bought in 1988 cost 350 dollars. so thank God this fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rellia from PADUCAH, KY
- Parts Used:
- 4163646
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Tried to screw button retainer in as instructed and screws did not fit-even using screwdriver to try and work t
Screwed in as far as I could get it but it never went flush with the wall of the compactor like the factory placed ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianne from ORANGEVALE, CA
- Parts Used:
- WPW10242557, 882657
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Compactor was white, changed appliances to black, put front panel and footpedal on to update appearance.
It was quick and easy, even for someone with limited "honey-do" experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ROSWELL, NM
- Parts Used:
- 882688
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
One of the roller wheels was worn out
Removed drawer
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid back into cabinet
inserted drawer
tested
Works as good as new
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid back into cabinet
inserted drawer
tested
Works as good as new
Was this instruction helpful to you?
Thank you for voting!