KUCS03FTPA0 KitchenAid Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roger from Grantham, NH
- Parts Used:
- 882688
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Trash bin would not roll out completely
-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Gillette, WY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Compactor would not return to starting position
Like others who experienced this problem, I removed compactor from under the counter and laid it on its side. I removed the screws holding the cover plates to the motor and gear/chain box. The larger (4" +/-) plastic drive gear which moves the chain that lowers or raises the compactor ram was broke. Using a socket and ratchet, I turned the shaft the gear was attached to in a counterclockwise direction and moved the compacting ram from the bottom position to the top so I could finally open the door, It takes a lot of turns to move the compacting ram to the top so be patient. I then loosened the bolts, in the base, that holds the motor secure and slid the base toward the broken gear putting slack in the chain. I removed the split ring from the shaft and removed the sprocket which originally is part of the gear but was left on the shaft when the gear broke in three places. I elected to not remove the original washer and spacer and put the new gear with sprocket on the shaft, put the chain on the socket and installed the split ring. Slid the motor base back to original position putting slight tension on chain and a proper clearance between the gear and drive shaft (sheet of paper seperation). Reinstalled the covers, tested and was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SALEM, NY
- Parts Used:
- W10165295RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Paper & Plastic 15” Compactor Bags not available
I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.
I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.
I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Dallas, GA
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
compactor wouldn't shut off
changed out the switch and that fixed the problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith V from Studio City, CA
- Parts Used:
- WP777328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The compactor rubber guard was torn.
Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Rumson, NJ
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not compact
It was very easy. I unscrewed the broken acuator and screwed the new one on. It took less than 5 minutes. Much better than paying a repairman $150 for a service call. This part actually breaks often so I ordered 3 or the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mona from San Diego, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
ram wouldn't go up or down.
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John B from ARDEN, NC
- Parts Used:
- W10342596
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Would have been nice to have known that the replacement switch operated in the opposite fashion from the original switch. Also, kit was missing the two screws to attach the new lever operator.
I had expected to just have to install a new spring steel "L" shaped switch operator to replace the one that had broken off. Installation of the new switch and redesigned operator was difficult in tight quarters. Good news, four hours later compactor works as advertised. Hope that the revised design works well and for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIMBERLY from Tahoe Vista, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Was not turning on to crush trash
Easy, called a repair person to install...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- avi from WOODLAND HLS, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Actuator broke off ordered new one
Step one-read instructions; step two-follow them! Really not that hard. Pull the compacter out. Take four screws off the top plate. Take 8 screws out the face plate. Disconnect old actuator install new one. Put the cutout over the new one. Drill ONE hole with template. Screw the one in. Now drill the second hole out-but make sure its level dont be a tool and make it all crooked. Then screw it in place. Put the face plate back in with the 8 screws and put the top plate back on. Now remove foot assembly and old actuator lever from drawer. Install new rubber thing a bobber and put the foot assembly back together. Put it all back in smack it with a hammer 32 times add duct tape and voila donzo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Houston, TX
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Compactor piston stuck in down position and couldn't open!!!
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ALICE, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bad gears and a bad switch
Put the parts in and reinstalled it back in it place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- WP9871602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
Roller was flat
Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from ASHEVILLE, NC
- Parts Used:
- 882688
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from CLARKSTON, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!