66514732111 Kenmore Trash Compactor - Instructions

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.

I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!

At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behind the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)

Replaced the limit switch. This did not alter the problem. Took off the On/Off/Start switch and dissasembled. I found the the Start switch was stuck in the on position. I reassembled the switch mechanism assuring that the Red "ON" indicator moldings were correctly positioned and reassembled everything. The Compactor now works properly. Need to add "Check the Start switch" to diagnosis.

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

Looking at the information I found online it was either one of 2 things the directional switch was bad, or the drive gear was broken. I replaced the directional switch 1st since that was the easiest and that did not solve my problem. I put it all back together and thought about it for a little while. After a couple of days. It occurred to me that I could see the ramrod's spinning as the plunger goes down, then when the plunger reached as far as it would go. The ramrod's would stop spinning. I reasoned that the problem had to be somewhere between the motor and those rods when I opened up the bottom of the trash compactor, Iran the cycle again and I could see that the drive gear was still spinning, but the chains to the ramrod's were not spinning. Once I saw that I realized that the sprocket that was attached to the drive gear had broken. The sprocket is metal and the drive gear is plastic and they fit together perfectly, but through age or stress. The plastic have become rounded and no longer fit perfect on that nut when you applied a good deal of pressure. I didn't have the tool that I needed to replace the small drive year. I think you need some kind of a punch to get that pin out. So I left that one in place loosened the nuts that hold the motor in place to create some slack in the chain chain came off the new drive gear one on. I tightened the motor back up in the correct position is reassembled everything and it's working perfect again.

Ordered new door hinge and used available You Tube Video. to assist in installation. Not a very difficult job, however that did not solve the problem. Then in an attempt to complicate the solution, I again removed the door and took the entire inside cover off. The entire latch mechanism fell on the floor. It took a very long time to determine how the latch mechanism was placed. Finally with the help of a neighbor the latch was placed back into position, the glass and screen replaced and finally all the plastic molding seated and screwed tight. Guess what the latch now seated correctly and appears to work correctly.

All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.