6228416001GO Kenmore Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from ALICE, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bad gears and a bad switch
Put the parts in and reinstalled it back in it place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from TACOMA, WA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Trash Compactor ram will not move while motor running, stripped power nuts
Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearing cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Flagstaff, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Compactor would not open. Ram was down
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from salinas, CA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
Trash Compactor didn't work
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmen M from Port Orchard, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Trash carier wore out
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from MUNCIE, IN
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEWBERRY, MI
- Parts Used:
- WP9871602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Rollers wore out
Removed and replaced in less than 15 minutes. Works like new again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from JEFFERSON CTY, MO
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The previous handle broken in half.
There were two screws holding the handle on, We removed the two screws, removed the broken handle and screwed the new handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Greene, RI
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
It is held on with three screws. The PartSelect was the only web site that showed me a picture of the part I wanted. The other web sites said it was no longer made. It was shipped out the day I ordered it, and took a minute to install it. Will order again from your company - great service - thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from BENNINGTON, VT
- Parts Used:
- WP777533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
a plastic bag got caught around the screw and the flange on the nut broke so it couldn,t raise one side so the door was jamed at an angle
I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheila from PINE BLUFF, AR
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
compactor would not compact the trash
took appliance out of cabinet, found the problem to be two nuts on the big screw bars that drive the compaction machine up and down. These things were wore out. We replaced them and turn the electricity back on and tried the compactor and it worked perfect. Of course here was to top cover that had to be removed and reinstalled . all in all it wasn't to difficult. A new machine cost 1100 dollars. This old one bought in 1988 cost 350 dollars. so thank God this fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WILLIAMSBURG, VA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Power nuts stripped
Only needed a flat blade screwdriver and a socket set to remove the top and the "cages" that held the power nuts. Failed to properly restrain the ram but didn't effect the repair. Installed the new power nuts outside of the unit then placed the ram assembly on the worm screws and all was well. Applied grease to the worm screws after assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from DENNIS, MA
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had a newly cracked handle on a 36 year old trash compactor.
Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathrine R from OKLAHOMA CITY, OK
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!
So glad you had the part. It was pricey, but way less than a new trash compactor!
Was this instruction helpful to you?
Thank you for voting!