6651350593 Kenmore Trash Compactor - Instructions

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screws from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

I removed 3 screws from the back and 2 smaller screws from the sides. I removed the broken handle, installed the new handle and inserted the 3 screws. The 3 screw hole aligned perfectly. The replacement part did not have predrilled holes for the 2 side screws so I drilled the holes and inserted the 2 smaller screws. Job done in short time.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!

Replaced handle. Very Easy.

The repair was simple and expensive for a little piece of plastic that was the wrong color and only color available. We have a white trash compactor and had to order a black one. The hardest and most time consuming part of the repair was painting the handle. In order to paint a Black Plastic handle white we had to use special primer and special paint. Before using the primer, we had to wash the plastic handle with paint thinner, then rinse and let dry completely. Other than the cost and the aggravation, it was fine. And it was less than buying a new one. : )

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

Took out old gears replaced with new very easy with your dirictions.

replaced the large gear and put it back together.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Very simple, changed the gear, adjusted the drive and tested. Very straight forward.

First off....I was surprised at how inexpensive the drive gear kit was. As others commented, they fit perfectly and I believe will fit other manufacturer's models since there is a lot of cross branding. The Drive gear replacement itself would be easy as described by others so I won't repeat that. However replacing the plastic tubular "ram stops" on the screw drive was a challenge since there are no "helpful hints" in the blog. To do that you have to work from the top and sides. Needed to remove the two gear cams where the screw drives are seated on the bottom of the unit, then (working with the unit on it's side)you have to raise the whole (heavy) plunger that is attached to the drive screws high enough to remove the old tubular ram stops and bushing and replace. To raise the plunger assembly out from the top you have to remove the sheet metal top plate of the unit....and....importantly remove the control panel on the front where the switches are. There is a limiter switch that has a metal arm which engages a plate on the plunger to stop the unit when it reaches the top. You need to remove that switch to be able to raise the plunger assembly high enough to get the new parts on the screw drive. Put all that back together and then go on to the gear replacement as described by others which was straight forward. Very messy job with all the grease and garbage residue. I am pretty handy figuring these things out, and there may be an easier way, but next time I will call a pro or replace the whole compactor.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian