6657464100 Kenmore Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Huntingdon Valley, PA
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle had cracked
So impressed with this Company. Was about to buy new trash compactor, because we couldn't find a handle for an old Frigidair. Found website and on Friday ordered part (only $57...a new compactor would have cost $800). Part arrived ONE DAY LATER and was immediately easily installed by taking out old part which involved unscrewing it and installing the new one using the existing screws. THANK YOU.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from lincoln, AR
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stripped pinion gear
I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Carver, MA
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle was broken and needed to be relaced.
I removed 3 screws from the back and 2 smaller screws from the sides. I removed the broken handle, installed the new handle and inserted the 3 screws. The 3 screw hole aligned perfectly. The replacement part did not have predrilled holes for the 2 side screws so I drilled the holes and inserted the 2 smaller screws. Job done in short time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Belmont, NH
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
20+ plactic gears striped them selfs who da thunk
took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janie from mcHenry, IL
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the switch did not click off
very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Refugio, TX
- Parts Used:
- WP608732
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Drawer Handle Broke
Replaced handle. Very Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Fairmont, WV
- Parts Used:
- WP608732
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drawer handle was broke.
The repair was simple and expensive for a little piece of plastic that was the wrong color and only color available. We have a white trash compactor and had to order a black one. The hardest and most time consuming part of the repair was painting the handle. In order to paint a Black Plastic handle white we had to use special primer and special paint. Before using the primer, we had to wash the plastic handle with paint thinner, then rinse and let dry completely. Other than the cost and the aggravation, it was fine. And it was less than buying a new one. : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candace from Ocala, FL
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Ram stuck in down poaition
Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willow Creek, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Primary Power Transfer Gear Split in Half
Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partselect part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph N from Wheaton, IL
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ram was stuck in the down position
changed out the big gear that was broken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tena from Parker, CO
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
compactor wouldn't compact
bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from red bluff, CA
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broken rotary switch
remove drawer remove two phillip screws lift off front panel remove wiring and plug into new switch.slide switch through the hole in panel install nut reinstall panel screws and drawer job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Quincy, IL
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
the compactor was stuck in the down position
Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Campbell, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Large plastic gear cracked in half. Compactor was stuck in the compact postition
replaced the large gear and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from DENNISPORT, MA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken drive gears
Took out old gears replaced with new very easy with your dirictions.
Was this instruction helpful to you?
Thank you for voting!