6651396581 Kenmore Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Templeton, CA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Compactor ram would not return to the top. The threaded bushings had broken off the wings that held them in place, causing them to spin.
I held up on the compactor ram as i loosened the two screws on each of the two retaining cups. I then unscrewed the threaded bushings and lifted the ram out of the unit. I then cleaned the surface of the tracks on which the ram guides up and down and applied a thin layer of silicone grease to those surfaces as well as the threaded rods. . I placed the ram back into the unit and held it in place as i replaced the threaded bushings and their respective caps. Unfortunately i neglected to move the limiting switch that stops the ram when it reaches the top of the cycle and I broke the lever that contacts the ram and subsequently activates the stop switch. so i removed the ram and removed and inspected the switch. It was broken beyond repair so i ordered a new switch from the same place I purchased the threaded bushings and am waiting for them to arrive. Lesson learned, pay attention to the sequence by which the original parts are removed and understand how the system functions so that you can remember to put it back in the right order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ALICE, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bad gears and a bad switch
Put the parts in and reinstalled it back in it place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DELAWARE, OH
- Parts Used:
- WP777811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Flagstaff, AZ
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Compactor would not open. Ram was down
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from salinas, CA
- Parts Used:
- WP777533
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
Trash Compactor didn't work
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmen M from Port Orchard, WA
- Parts Used:
- 13030RP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Trash carier wore out
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from MUNCIE, IN
- Parts Used:
- 675382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEWBERRY, MI
- Parts Used:
- WP9871602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Rollers wore out
Removed and replaced in less than 15 minutes. Works like new again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathrine R from OKLAHOMA CITY, OK
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!
So glad you had the part. It was pricey, but way less than a new trash compactor!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from SPRING GROVE, IL
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer handle
Removed two screws on back of pull out door. Pulled up on handle, came out easily, slide the new one in, replaced the screws and done. Less than 5 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from DENNIS, MA
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had a newly cracked handle on a 36 year old trash compactor.
Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from BENNINGTON, VT
- Parts Used:
- WP777533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
a plastic bag got caught around the screw and the flange on the nut broke so it couldn,t raise one side so the door was jamed at an angle
I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from JEFFERSON CTY, MO
- Parts Used:
- WP608732
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The previous handle broken in half.
There were two screws holding the handle on, We removed the two screws, removed the broken handle and screwed the new handle on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Greene, RI
- Parts Used:
- WP608732
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
It is held on with three screws. The PartSelect was the only web site that showed me a picture of the part I wanted. The other web sites said it was no longer made. It was shipped out the day I ordered it, and took a minute to install it. Will order again from your company - great service - thanks.
Was this instruction helpful to you?
Thank you for voting!