6228419001GO Kenmore Trash Compactor - Instructions

The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Looking at the information I found online it was either one of 2 things the directional switch was bad, or the drive gear was broken. I replaced the directional switch 1st since that was the easiest and that did not solve my problem. I put it all back together and thought about it for a little while. After a couple of days. It occurred to me that I could see the ramrod's spinning as the plunger goes down, then when the plunger reached as far as it would go. The ramrod's would stop spinning. I reasoned that the problem had to be somewhere between the motor and those rods when I opened up the bottom of the trash compactor, Iran the cycle again and I could see that the drive gear was still spinning, but the chains to the ramrod's were not spinning. Once I saw that I realized that the sprocket that was attached to the drive gear had broken. The sprocket is metal and the drive gear is plastic and they fit together perfectly, but through age or stress. The plastic have become rounded and no longer fit perfect on that nut when you applied a good deal of pressure. I didn't have the tool that I needed to replace the small drive year. I think you need some kind of a punch to get that pin out. So I left that one in place loosened the nuts that hold the motor in place to create some slack in the chain chain came off the new drive gear one on. I tightened the motor back up in the correct position is reassembled everything and it's working perfect again.

The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

Removed panel and replaced it...

The repair was simple and expensive for a little piece of plastic that was the wrong color and only color available. We have a white trash compactor and had to order a black one. The hardest and most time consuming part of the repair was painting the handle. In order to paint a Black Plastic handle white we had to use special primer and special paint. Before using the primer, we had to wash the plastic handle with paint thinner, then rinse and let dry completely. Other than the cost and the aggravation, it was fine. And it was less than buying a new one. : )

Replaced handle. Very Easy.

I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

I removed 3 screws from the back and 2 smaller screws from the sides. I removed the broken handle, installed the new handle and inserted the 3 screws. The 3 screw hole aligned perfectly. The replacement part did not have predrilled holes for the 2 side screws so I drilled the holes and inserted the 2 smaller screws. Job done in short time.