TC507B Jenn-Air Trash Compactor - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from San Diego, CA
- Parts Used:
- 675382
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Erratic starts and direction of ram. Switch tested bad.
Ordered part and received it in two days. Unplugged the compactor from wall outlet. Removed two screws holding control panel in place, marked proper wire location on rear of panel, disconnected push-on terminations from start/run switch. Removed knurled nut holding start/run switch onto the control panel and substituted the new switch. Reassenbled everything in reverse order to disassembly and plugged power cord back into the wall outlet. No further work required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Newark, DE
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Broken plastic gear
Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from DENNISPORT, MA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken drive gears
Took out old gears replaced with new very easy with your dirictions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Campbell, CA
- Parts Used:
- 882699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Large plastic gear cracked in half. Compactor was stuck in the compact postition
replaced the large gear and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from WAYLAND, MI
- Parts Used:
- 882699
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
plastic gear broke in half
Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Jacksonville, FL
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drive motor would not turn off after completing cycle
Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Goshen, KY
- Parts Used:
- 882699
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken plastic drive gear
Very simple, changed the gear, adjusted the drive and tested. Very straight forward.
Was this instruction helpful to you?
Thank you for voting!