ST21HPXLQ02 Whirlpool Refrigerator - Instructions

The bent hinge caused a bad seal which let in air into the freezer, so there was a ton of frost build up. I ordered the parts, and they came in 2 days! I figured what tools I needed, got my wife to help hold things, and in 20 minutes it was like new.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

install ice maker 2 screws wire harness pluged in done

Took out the old, cracked, crisper unit and removed the white trim piece on the handle so that we could re-use it on the new crisper unit (which, in spite of the $90+ price tag did not come with new trim). The whole thing took 3 minutes to do.

Make sure you order the right parts. The bar needs 2 caps so don't make the mistake of only ordering one. Once you push in the end caps into the retainer bar, gently insert bar into slots on door. Right parts will create a perfect fit.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

I was prepared for the part not to fit because it's a 23-year-old fridge, but it fit perfectly, no issues whatsoever. I plan to buy a crisper drawer as well. Glad I found this vendor.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store

Replaced the drawer

Just installed the 4 screws

Retainer bar was a little long but husband used a saw to make smaller (the part said it was a similar to my model- Maytag no longer made this made) It was perfect -- ow I have a whole new usable shelf!!

The first part I changed was the defrost timer but it did
not solve the problem, I replaced the bi-metal defrost sensor
and I have the same problem.

I can defrost by turning the clock manually and heater works.



























problem.

Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.

I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.