WRS321SDHB00 Whirlpool Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

Steps to replace Whirlpool evaporator fan motor
1. Watch numerous DIY Youtube videos
2. Move frozen food to refrigerator section, close refrigerator door
3. Cut power to refrigerator
4. Remove all shelves and bins in freezer section
5. Back panel has two parts, a top and a bottom section
6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt
7. Gently pull and work top panel out
8. Remove screw bolts from all four corners in lower panel and remove bottom panel
9. Verify power has been turned off
10. Unclip grounding wire
11. Unclip evaporator fan motor from power
12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable.
13. Remove plastic fan with firm pull
14. Unclip bottom brace to remove evaporator fan motor
15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets
16. Install new evaporator in cradle and clip-in the bottom brace
17. Install new fan blade on motor
18. Place cradle with new evaporator fan motor back in freezer
19. Reclip power and ground wire
20. Turn on power and test if working correctly
21. Turn off power
22. Complete steps from 8 to 2 in reverse

Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.

Found the filter door in toe kick under freezer door. Opening the door ejected the old filter. Direction indicator arrows were found on inside of filter door, rotation of filter to match arrows important. Pushed new filter in to stop, closing door completed insertion of new filter.

No repair needed. Just inserted the storage bin onto the hooks provided on the inside of the door.

ordered new filter, removed old filter from fridge, and installed new one

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.

I was unable because you do not even carry the par that you still advertised on you sit and I was charged $20.00 to return the par. The representative was very rude and accused me of ordering the incorrect part as if I don't know the difference between a hose and a filter. When i expressed the poor customer service he disconnected the call. I will never patronize your business or recommend it to anyone.

Unplugged freezer turned off water removed 3 nut screws Unplugged old ice maker installed new ice maker

Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.