WRF555SDHB00 Whirlpool Refrigerator - Instructions

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE!

Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

You remove the white frame from around the old pan by popping it off from the bottom being careful not to break it. Install it on the new pan using the reverse procedures. Popping it on starting at the bottom. Very easy

Removed the whole ice maker unplug one wire harness replaced ice tray with new one.
Very simple.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Thank you for the prompt delivery. I thought it was going to be a big problem to get a replacement shelf, but I ordered online and had my part in 3 days! Very easy to insert. Did lay carton on the floor and pulled out the insert. At 83 my strength isn't what is used to be, but it came out pretty easy. I am beyond thrilled with the service. Thank you.

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.

By the way - the part got here really fast - thanks for the great service.

Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.