WRF540CWHB00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PAUL from SOUTH WALES, NY
- Parts Used:
- W10443319
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freeezer door icing up
Loosen 4 screws remove door wipe off frost pull old gasket out of slot push in new gasket instal door that was it. No help need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Cream Ridge, NJ
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
chef drawer cover
take the old one out replace with new once - no instructions required, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Roseville, MI
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass on pantry door
Pulled the broken pantry door off, and snapped the new door in place. Vry simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from San Antonio, TX
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from TUNNEL HILL, GA
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light was blown
I turned the light bulb into the socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BRUCE TWP, MI
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket has 2 tabs on the side that opens. Both had torn. Also one vertical slit halfway up the gasket
Followed your instructions: gasket came coiled in the box and was slightly curled up. Both left & right side of gasket were linked. Followed your instructions to properly restore the shape. Pulling the old gasket off and installing the new one took just a few minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from EVERETT, WA
- Parts Used:
- W10443319
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Snow in freezer. Gasket separating and magnetic strip exposed
The old gasket peeled out easily. No tools needed. The replacement gasket fit right in the groove. I did not need to immerse the gasket in warm water or use a hair dryer. Nifty trick: once the new gasket is in place, close the freezer door. Run your finger in the center groove of the gasket, which will push the magnet against the fridge. Leave the door closed for an hour. The gasket has then assumed a perfect fit and will continue to fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PENNSVILLE, NJ
- Parts Used:
- WP12722803W
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Piece that makes the left side door close
Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Bend, OR
- Parts Used:
- WPW10289497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door bin on a friend's refrigerator had a crack in it that quickly grew to a much bigger crack.
You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Bluffton, SC
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The filter was clogged.
Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from WAKE FOREST, NC
- Parts Used:
- W10884390
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Existing icemaker would freeze up, stop making ice.
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from LAVEEN, AZ
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No problem
Just pulled the old one off with fingers, and pressed the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from friendswood, TX
- Parts Used:
- WP12656018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken right side peg for deli drawer cover
First, make sure you have the correct part. I had trouble with mine, at first, until I realized that I had received the wrong part... it was same shape but larger. To begin, remove both fruit/vegetable drawers. Remove deli drawer. Remove deli drawer glass panel with both supports. Remove 3, 1/4" hex screws that attach end-cap. Disengage temp control slide and arm from end-cap by carefully moving parts in the direction where they will disengage. Remove temp control slide from end-cap. Now that end-cap is out, remove 2 screws that hold metal drawer slide to end-cap. Attach drawer slide to new end-cap. Attach temp contol slide and connect the plastic arm. Attach end-cap to refrigerator. Replace glass shelf, supports and drawers. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JimBob from CRAWFORDSVLLE, AR
- Parts Used:
- W10884390
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom freezer ice maker quit making Ice
Used a deep well 1/4" nut driver. Loosen 4 screws on inside of door and slip it up and off rack. Remove 2 screws on bottom of ice maker. Loosen top 2. Slip up of screws, unplug ice maker and remove.
Was this instruction helpful to you?
Thank you for voting!