WRF555SDFZ05 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RICHARD from LINBROOK, NY
- Parts Used:
- W10874836
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Plastic pin that supports the plastic drawer cover was broken.
After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Roseville, MI
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass on pantry door
Pulled the broken pantry door off, and snapped the new door in place. Vry simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Los Angeles, CA
- Parts Used:
- WPW10326469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken guide rail
This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Cream Ridge, NJ
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
chef drawer cover
take the old one out replace with new once - no instructions required, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from SNELLVILLE, GA
- Parts Used:
- WPW10714545
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
FROST, ICE buildup along and inside the bottom of freezer and door
Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from LARGO, FL
- Parts Used:
- W10830055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn door gaskets
Took out the old and installed the new.. The fit was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Bluffton, SC
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The filter was clogged.
Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David L. from Red Rock, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The orignal proberm was broken hinge on End Cap
There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morten from SAN JOSE, CA
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Refrigerator Repair - How to Replace the Pantry End Cap
Broken bottom drawer lid mount
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Jacksonville, FL
- Parts Used:
- W10316760
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Lower Freezer worked fine, but upper refrigerator would not cool.
I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After replacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from MUNDELEIN, IL
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Did not need filter
Unscrew filter. Screw on filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merrill from Colorado Springs, CO
- Parts Used:
- W10874836, W10874836, W10827015, WP67004515, WPW10326469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pantry Lid broken, center rail broken, pan corner cracked
Remove broken parts with philips screw driver (6 screws). Replace encaps while attaching pantry drawer lid. Insert center rail and new drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WESTERVILLE, OH
- Parts Used:
- W11658402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken black plastic spring mechanism inside freezer rail
Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from OLYMPIA, WA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy damper
Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Fountain Inn, SC
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Peg for the Deli Drawer Lid BROKE - right side
Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!
Was this instruction helpful to you?
Thank you for voting!