GB2SHDXPB12 Whirlpool Refrigerator - Instructions

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

replaced inlet valve per insert with part, easy

Very easy to order from parts select. Took seconds to replace.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

To repair the problem,I ordered a new gasket. Once I received the gasket, I laid it flat on the floors and hot the blow dryer and blow out the creases in the gasket. I then took off the door by removing the four screws from the door and rest the door on the table. I then removed the old gasket and replaced it with the new one. It took about 15 minutes. My frig. Stop freezing up.

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Snapped in new part

long story, but good experience with Partselect.com...ordered a defrost heater as I had to replace same 15 years earlier, when part arrived I managed to test continuity of old heater in place and appeared fine (unless due to intermittent break that opened with heat) - so went ahead and order defrost thermostat and arraigned for return of heater (kept until testing after installation of the thermostat) - replacement of thermostat pretty easy - be sure to watch video of how to remove freezer rails for bottom freezer.
When I plugged back in the compressor wouldn't start, tried to and then shut off over and over. I had the dreaded thought that either I had put a leak in the coils or the compressor had failed due to overwork with failed defrost mode. Fingers crossed I ordered start capacitor and relay kit...sure enough when I removed the old capacitor and relay - I heard loose parts in the relay and pieces fell out when I shook it. installed new relay/capacitor and the fridge works like new - 21 year old Amana - very well engineered and easy to work on - great videos on disassembly re-assembly - when I replaced the heater 10 years ago I couldn't figure out how to remove side rails - no idea how I managed to pull the bottom of the cooling unit past the rails to remove and replace the heater.
I would recommend doing what I did, unless you are sure of the failure mode - which is to leave the back panel open for a day in the freezer after repair to be sure the defrost mode is working.

knelt down, positioned replacement kickplate; popped into place, stood up!

took longer to open the box and peel bubble wrap off item than to replace it!

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.