6FAR Whirlpool Refrigerator - Instructions

Removed two screws, replaced handle, replaced the two screws. This was so simple! I can't believe we put up with the inconvenience for so long before fixing it!

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

changed out the big gear that was broken

Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partselect part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.

I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.

Hey real easy, remove old handle and replaced with new one. had to drill holes for the ends.

Removed the three screws holding the broken handle to the compactor and used them to attach the new handle.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

replaced with new that arrived very quickly I am very happy since I put it off a long time. If I new how easy I would have done it 3 yrs ago. Thanks, Sheila

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

replaced the large gear and put it back together.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

First off....I was surprised at how inexpensive the drive gear kit was. As others commented, they fit perfectly and I believe will fit other manufacturer's models since there is a lot of cross branding. The Drive gear replacement itself would be easy as described by others so I won't repeat that. However replacing the plastic tubular "ram stops" on the screw drive was a challenge since there are no "helpful hints" in the blog. To do that you have to work from the top and sides. Needed to remove the two gear cams where the screw drives are seated on the bottom of the unit, then (working with the unit on it's side)you have to raise the whole (heavy) plunger that is attached to the drive screws high enough to remove the old tubular ram stops and bushing and replace. To raise the plunger assembly out from the top you have to remove the sheet metal top plate of the unit....and....importantly remove the control panel on the front where the switches are. There is a limiter switch that has a metal arm which engages a plate on the plunger to stop the unit when it reaches the top. You need to remove that switch to be able to raise the plunger assembly high enough to get the new parts on the screw drive. Put all that back together and then go on to the gear replacement as described by others which was straight forward. Very messy job with all the grease and garbage residue. I am pretty handy figuring these things out, and there may be an easier way, but next time I will call a pro or replace the whole compactor.

Very simple, changed the gear, adjusted the drive and tested. Very straight forward.