IK4TXWFDW00 Whirlpool Refrigerator - Instructions

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

first remove ice maker 1-screw on the bottom all the way out and two screws on the top half way out slide up and out and unplug wiring as you remove then remove back panel unplug ground wire remove screws that hold fan assembly unplug wiring remove pressed on fan blade put new motor in reasemble and it was good to go

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

replaced old one installed new one

Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.

Per instructions

Switch off power at mains outlet. Pull off the front trim panel on the control box at top of the refrigerator compartment (it is just clipped into place). Behind are two screws which you remove. Remove the bulb and also two screws underneath and towards back of the control box. You can then pull down the control box. The defrost timer board is now visible and can easily be switched out (it comes with instructions how to do this). This job too no more than 20 minutes and saved me buying a new refrigerator at $1000.

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

Following the info on another post from partselect site: Unplug the main refridgerator line from the outlet. Removed icemaker(didn't have this hooked up to operate), 2 screws and 1 hex nut; removed back panel of freezer wall (interior), be mindful of wiring harness on the left of panel, 2 hex nuts: unplugged fan motor from wiring harness, removed motor with 2 screws, gently, but firmly pulled fan blade off (a little tricky due to housing bracket around it) carefully noting 2 soft rubber gaskets that holds the unit in bracket. replace motor with new one ... follow above steps in reverse. helpful to have a small flashlight. make sure soft rubber gaskets are seated in place. Fan blade requires a firm but gentle push back on the metal post ... bottom of back panel seats over an opening in order for it to fit snug against the wall. I am totally satisfied with the info and seamless, expediant service with partselect ... thank-you so much ..

Removed the ice maker (3 screws) removed the back plate (2 screws) Remove the bracket holding the fan in (2 screws) Remove the rubber mounts on the old motor and the fan itself off the old motor. Then put it all back together in reverse order.

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( quite easy )

First i pulled the electrical plug from the socket so the refrigator was off than I removed 5 screws (3 of those holding the ice maker). pulled the icemaker toward the front and removed it I than took off the back of the freezer panel,(the back panel was removed by pulling the top of the panal towards me it came right out of the freezer) I removed an additional 2 screws holding the evaporator fan motor. Than I used pliers to squeeze the mounting bracket tabs (white tabs BOTTOM OF MOTOR BRACKET). I then disconnected the electrical FAN MOTOR PLUG and removed the motor. i than pulled the fan blade from the motor (fan blade is only a pressed onto the motor shaft.I than pressed the fan blade back unto the fan motor and reversed the above directions

i removed the back cover off in the icebox,removed the fan motor,replace the new one now it works fine.very easy to do,saved alot of money on a new one.