WRS335FDDB02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from STATEN ISLAND, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford Bell. from WASHINGTON, DC
- Parts Used:
- W10862460
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Water was not dispensing from the refrigerator.
Installed a new water filter housing unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Covington, GA
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
my drum was broken and would not put ice down to be used
I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Chandler, AZ
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Auger Busted
Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MESQUITE, NV
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ice container bin cracked and had a hole in it.
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Bloomington, IL
- Parts Used:
- WPW10276341
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the shelves broke and needed to be replaced
It took less than one minute to open the box and place the shelf in the fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Camille from Glen Ellyn, IL
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer was icing up and leaking. Refrigerator side would not keep cold.
We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
Was this instruction helpful to you?
Thank you for voting!
door would not close automatically and replaced torn gasket.
removed door took out single bolt pried out cam put new one in returned bolt rehung door. 15 minutes
pulled old gasket out cleaned area where gasket was and lube edge of new gasket with vaseline starting at top slide gasket in then sides last was bottom which was hardest. 20 minutes
pulled old gasket out cleaned area where gasket was and lube edge of new gasket with vaseline starting at top slide gasket in then sides last was bottom which was hardest. 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from EASTON, PA
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
just added new shelf - perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Liberty hill, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Ice Bin Auger Drum was broken.
First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ENDWELL, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from FAIRVIEW, NC
- Parts Used:
- WP2188656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
broken drawer
It was a drawer I removed the old one and slid the new one in. Took longer to fill out this form than to replace the drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VANCEBURG, KY
- Parts Used:
- WPW10179146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inlet valve was broken at the water line connection
Changed inlet valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damien from MILTON, FL
- Parts Used:
- WPW10515057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light out
Small flat head screw driver.Light is basically a computer module with plug connector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from TUCSON, AZ
- Parts Used:
- WPW10515057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light out, refrigerator lights dim.
Used a screwdriver to pop the catches and unplugged the light from the top of the freezer. Plugged the new light into the wire connector and pushed the assembly back into freezer top. The freezer light and all the refrigerator lights are now bright.
Was this instruction helpful to you?
Thank you for voting!