WRF532SNBM00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from RACINE, WI
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door gasket was cracked and torn
Replacement gasket extremely easy to install. Used hair dryer to soften and straighten out “kinks” in replacement gasket. Pulled old gasket out of groove in refrigerator door. Lined up corners of new gasket and pressed into place with my fingers. Went in exactly as video showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from BALD KNOB, AR
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber liner around the refrigerator door was splitting and cracking
I watched the video and it took away my trepidation. I did what it said and it went right in!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lane from EVERETT, WA
- Parts Used:
- WP12722803B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
One of the plastic fasteners had broken so the entire part needed replacing.
Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ATLANTIC BCH, FL
- Parts Used:
- W10443315
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer Compartment Gasket Replacement
My freezer compartment gasket was torn and needed replacement. This was on a bottom freezer Kenmore refrigerator. I couldn't find directions for how to take the freezer compartment door off, and figuring out how was the hardest part. Here are the instructions:
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NEWTON, NJ
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fridge was leaking water because of bad drain
Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues
Fixed the problem
Have had no more drain issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Lou from RNCH DE TAOS, NM
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed a new gasket for the right side door
Watched the video on this site, followed the instructions to lay the gasket flat and warm it with a hair dryer, removed the old gasket, and popped the new one in. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from GRANTS PASS, OR
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad gasket
Pulled off old gasket
Put new gasket in the groove
Gasket fit perfectly
Thank you
Put new gasket in the groove
Gasket fit perfectly
Thank you
Was this instruction helpful to you?
Thank you for voting!
torn gasket
gasket pulls out of groove in the door very easily. insert new gasket in the groove. very groovy!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Blairsville, GA
- Parts Used:
- WPW10284685, WPW10284684
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Parts ordered on Sun Arrived Tues (local stores closed)
Talking with the service tech and youtube video it was a snap... Saved a service repair and a 25% parts mark up..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Riverside, CA
- Parts Used:
- WPW10671238, WPW10568041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Both pieces were broken.
Just replaced old with new. The glass shelf was good so just moved it to the new pieces. Everything fit perfectly, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ida Mae from MEDLEY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Gasket had a tear in it.
To repair the problem,I ordered a new gasket. Once I received the gasket, I laid it flat on the floors and hot the blow dryer and blow out the creases in the gasket. I then took off the door by removing the four screws from the door and rest the door on the table. I then removed the old gasket and replaced it with the new one. It took about 15 minutes. My frig. Stop freezing up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LAKE CITY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer freezing up. Frost everywhere.
Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LAKE CHARLES, LA
- Parts Used:
- W11447232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the light bulbs went out on my Whirlpool refrigerator.
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from WINSTED, CT
- Parts Used:
- W10619951
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining to pan. It caused an ice build up under the freezer draw
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!