WRF532SNBW01 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from LAKE CITY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer freezing up. Frost everywhere.
Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from RACINE, WI
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door gasket was cracked and torn
Replacement gasket extremely easy to install. Used hair dryer to soften and straighten out “kinks” in replacement gasket. Pulled old gasket out of groove in refrigerator door. Lined up corners of new gasket and pressed into place with my fingers. Went in exactly as video showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MIDDLETOWN, MD
- Parts Used:
- W11368721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right door seal was torn at top of door
I followed the remove and replace instructions in the Part Sect video when I ordered the seal. Pulled out the old seal by hand and installed the new seal. No tools needed, very easy. Took 10 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lane from EVERETT, WA
- Parts Used:
- WP12722803B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
One of the plastic fasteners had broken so the entire part needed replacing.
Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodolfo from SAN LEANDRO, CA
- Parts Used:
- W10830162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There’s moisture inside the refrigerator and there’s a section in the gasket that was broken.
Easily pulled out the gaskets off the refrigerator doors and replaced them with the new ones. The installation video was also a big help in the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from YUMA, AZ
- Parts Used:
- W10830162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rubber seal for right hand doors separated and allowed magnetic strip to fall out
Received gasket. Checked color and size. Because this unit is 33 inches wide one door is 3 inches narrower than the other. Removed shelves from door to provide more room to work. Took 15 seconds to pull out old seal and 1 minute to install the new one. Checked to make sure center sealing flap were on the center side of door. Started in upper corners, worked my way around the perimeter pressing in in with my fingers.
Took longer to R&R and wash shelves than to replace door seal.
VERY EASY
Took longer to R&R and wash shelves than to replace door seal.
VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. David from BRENTWOOD, TN
- Parts Used:
- WPW10350564
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Capacitor shorted out due to power surge.
Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NEWTON, NJ
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fridge was leaking water because of bad drain
Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues
Fixed the problem
Have had no more drain issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WINCHESTER, VA
- Parts Used:
- W11024089
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
No evap. fan function, freezer cold, refrigerator not cold.
My unit was a bottom mounted freezer, the door assembly and side out rack unit took more time then the repair. Once you take the back panel off it is just a matter of unplugging and two screws. Easier to pull fan mounting housing out to replace motor. Be careful its all plastic, pot off fan blades off shaft, pot out old motor, pot in new motor, slide fan blades back on shaft, make sure you get the mounting housing behind the duck that goes up to your refrigerator section, two screws and plug in connections and your done. Put back panel, rack and door assembly back in and you are friggen again, once you plug it in of course.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from Longview, WA
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I purchased a display model that was missing a part.
Snapped on the new toe grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from NORFOLK, VA
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Boyfriends freezer door wouldn’t shut completely
I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from WINSTED, CT
- Parts Used:
- W10619951
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining to pan. It caused an ice build up under the freezer draw
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GEORGETOWN, TX
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke my original Kickplate Grille
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LAKE CHARLES, LA
- Parts Used:
- W11447232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the light bulbs went out on my Whirlpool refrigerator.
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
Was this instruction helpful to you?
Thank you for voting!