WRT519SZDW01 Whirlpool Refrigerator - Instructions

I suspected the frig thermistor so I cut wires to the original. The new part was not a direct replacement, but was adaptable. I’m not sure the frig design would allow for an OEM replacement anyway. I clipped off the useless connector on the new thermistor and spliced the thermistor in by soldering wires appropriately. That was a bit difficult due to the short available length of the wires, and it didn’t solve the problem. Since it seemed like the damper responded normally to power-off resets and diagnostics using the onboard control buttons, I decided the main control board pretty much had to be the culprit. It was. Replacing the board was a piece of cake. Only a 1/4” nutdriver required, plus maybe a small screwdriver for prying here or there. Happy to have the frig working again.

After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Take screws out pull panel out unconnect the part connect new one and your done

Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!

Like you video

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!