WRT511SZDW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from FENTON, MO
- Parts Used:
- WPW10448874
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Refrigerator and freezer not cooling
It was easy to replace the start and run capacitors. But did not fix my problem, also replaced the evaporator fan still not fixed. Pulled refrigerator out of RV and ordered a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Manchester Center, VT
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from STERLING HTS, MI
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator light would not turn on.
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from MONTROSE, CO
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the track for the meat drawer shelf cracked
We took out the shelf, the new track snapped in place easily.
Part Select is an innovative answer to dyo repairs, very
helpful through process.
Part Select is an innovative answer to dyo repairs, very
helpful through process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LEWISBURG, KY
- Parts Used:
- WPW10392132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer cold, refrigerator warm
Simply cut wires from old bi metal and joined to new part with wire nuts. Simple repair, but it did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from KELSO, WA
- Parts Used:
- W10861519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken meat drawer shelf frame...
Removed shelf, removed shelf frame and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from San Francisco, CA
- Parts Used:
- W10861519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original meat drawer broke due to overloading. I ordered from PART SELECT but had the agent help me with the exact item!
Getting the right part was the key but I had the serial number and the agent in Nova Scotia helped me identify the part and using the 360 degree camera, I was
able to determine how it was going to slide into the shelf. It took less than 15 minutes and was extremely easy to install. Everything just slide right in. The agent was the key to my success!
able to determine how it was going to slide into the shelf. It took less than 15 minutes and was extremely easy to install. Everything just slide right in. The agent was the key to my success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from POWAY, CA
- Parts Used:
- W11025586
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Track was broken on both front and rear mount
1)Removed the drawer
2) used a 8mm nut driver to unscrew the 2 mounting bolt.
3) clean /disinfect the bottom layer of the refrigerator
4) mount the track and installed the 2 #8 hex head mounting screw
5) slide back the drawer
2) used a 8mm nut driver to unscrew the 2 mounting bolt.
3) clean /disinfect the bottom layer of the refrigerator
4) mount the track and installed the 2 #8 hex head mounting screw
5) slide back the drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from PELHAM, NY
- Parts Used:
- WPW10662129, WPW10448874
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
Freezer not cold
YouTube helped ,diagnosed problem ,found defective part removed and replaced with new part.
Is a little job on your knees
Is a little job on your knees
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TROY, IL
- Parts Used:
- WP2315539
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Fan motor died
First, made sure new fan worked then Placed back in bracket with bushings-only goes in one way, pushed fan back on. screwed bracket to back of freezer and ran the wires to their original place, plugged in the two plugs, put the back piece up attaching ground and pulling ice maker plug thru, screwed back on. Plugged in ice maker, mounted ice maker on freezer wall. Plugged it in. Exact reversal of how it was removed. Not a lot parts to get confused.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert G from AIKEN, SC
- Parts Used:
- WPW10279909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not working. Motor working, not getting water to icemaker.
Replaced inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CARLSBAD, CA
- Parts Used:
- W10837029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I was sent the wrong part
I ordered a handle for my refrigerator and received a washing machine part. Still waiting after a week for my return request to be processed Not happy with the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from BUFFALO GROVE, IL
- Parts Used:
- W10861519
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The original shelf that came with the refrigerator broke and we ordered a replacement.
The problem with the replacement part is that it didn't fit cleanly and doesn't slide well with the existing drawer.
We were disappointed.
We were disappointed.
Was this instruction helpful to you?
Thank you for voting!