WRT318FZDW01 Whirlpool Refrigerator - Instructions

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

I bought this refrigerator from a big box store w/o seeing the actual model, but was told the one I was buying was exactly the same only w/o handles sticking out. Not so. This model has no full-size freezer shelf even tho there are slots on both sides of the freezer for a full-size shelf. Whirlpool was no help, telling me I'd undo the warranty if I tried to put in a shelf that wasn't for that freezer, but I investigated & found the frig I originally saw, got its full-size freezer shelf model number, & voila! I'm now a happy camper with a better organized freezer. Freezer shelf fit perfectly, came intact due to being well-packed for shipment. Easy to install-just slid it into the shelf track slots.

Pull the top shelf out and slide the new part in

Removed the main top glass shelf from the fridge,slide meat drawer shelf into the side of the glass main shelf.Thats it,you can then install your meat drawer into the new meat shelf bracket.

removed old and installed new compartment door by hand.

Just took the entire glass shelf of refrigerator out and flipped over. I then slid the replacement rack on and replaced in refrigerator and slid the deli drawer on to rack. Very simple. Took maybe 3-4 minutes.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Using a screwdriver

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

1st; Remove all shelving
2nd; Phillips screws,= remove bottom cover, and bottom vent
3rd; Sensor is straight up- plug & play (see pic)!
DO NOT MAN-HANDLE.!
4th; Re-install vent & cover 'SLOWLY'.!
Please buy a "Freezer" thermometer. Good freezers work
around (+5* to -10*) even with food.

remove inside cover. meit ice collected, remove old part and install new part. about 1 hr.

$80 part motor fan replaced saved me $1000 or more on new fridge.

Called in and you guys helped out
You guys are the best.

Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since

Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that clips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.

I suspected the frig thermistor so I cut wires to the original. The new part was not a direct replacement, but was adaptable. I’m not sure the frig design would allow for an OEM replacement anyway. I clipped off the useless connector on the new thermistor and spliced the thermistor in by soldering wires appropriately. That was a bit difficult due to the short available length of the wires, and it didn’t solve the problem. Since it seemed like the damper responded normally to power-off resets and diagnostics using the onboard control buttons, I decided the main control board pretty much had to be the culprit. It was. Replacing the board was a piece of cake. Only a 1/4” nutdriver required, plus maybe a small screwdriver for prying here or there. Happy to have the frig working again.