7WRS22FDBW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Orange, CA
- Parts Used:
- 8201515
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker in the freezer section quit making ice cubes.
First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Liberty hill, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Ice Bin Auger Drum was broken.
First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damien from MILTON, FL
- Parts Used:
- WPW10515057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light out
Small flat head screw driver.Light is basically a computer module with plug connector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from COLUMBIA, SC
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced filter for ice maker
I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VANCEBURG, KY
- Parts Used:
- WPW10179146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inlet valve was broken at the water line connection
Changed inlet valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from SHERMAN, TX
- Parts Used:
- WP2309941
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken on one side.
The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from ISLAMORADA, FL
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door bin broke
had my wife install them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARI from STUDIO CITY, CA
- Parts Used:
- WPW10276348
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
THE SLIDE OUT SHELF WITH GLASS FRAMES WERE BROKEN.
I HAD TO BE CAREFUL...THE SHELF COST ME OVER $200/
iT WAS PACKED SAFELY AND THE GLASS SHELF ARRIVED SAFELY.
REMOVING IT FROM THE PACKING IS NOT TOO DIFFICULT...THE SHELF IS BROAD..
ONCE I WAS ABLE TO BRING IT OUT, I WAS ABLE TO REPLACE IT INTO THE REFRIGERATOR BY SLIDING IT INTO THE FRAME.
I AM NOT A HANDYMAN...BUT THIS WAS EASY.
iT WAS PACKED SAFELY AND THE GLASS SHELF ARRIVED SAFELY.
REMOVING IT FROM THE PACKING IS NOT TOO DIFFICULT...THE SHELF IS BROAD..
ONCE I WAS ABLE TO BRING IT OUT, I WAS ABLE TO REPLACE IT INTO THE REFRIGERATOR BY SLIDING IT INTO THE FRAME.
I AM NOT A HANDYMAN...BUT THIS WAS EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from JACKSONVILLE, NC
- Parts Used:
- WP1119017
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice deflector had broken.
Removed ice tray and unbolted front cover. Removed broken piece and snapped new ice deflector in place. Reinstalled front cover and put ice tray back into freezer. Cycled crushed ice, works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from N CHESTERFLD, VA
- Parts Used:
- WPW10321304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
simply set the new bin where the old one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from LAS CRUCES, NM
- Parts Used:
- WPW10318960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wanted an additional shelf. Slots for shelf were already there.
Shelf slid right in. Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from RANDOLPH, NJ
- Parts Used:
- WPW10179146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Loud banging after using water dispenser
Followed the extremely helpful video on the web site. It was easy to remove, replace, and install the new part, following their video. Saved time and money, and I didn’t lose anymore of my hair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from KLAMATH FALLS, OR
- Parts Used:
- WPW10178772
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked crisper drawer.
Removed old drawer and replaces with new one. A perfect fit. E-bay advertised free shipping, but their price was higher than PART SELECT WITH THE SHIPPING CHARGE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAUGERTIES, NY
- Parts Used:
- W10864399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper shelf glass missing
Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from BEAUMONT, TX
- Parts Used:
- WPW10178772
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
SIDE OF BIN'S RUNNER HAD WORN OFF
The hard part was getting the right part ordered!
The exploded view needs to be bigger as it is hard to differentiate.
A phone call fixed everything.
The exploded view needs to be bigger as it is hard to differentiate.
A phone call fixed everything.
Was this instruction helpful to you?
Thank you for voting!