7WRS22FDBW00 Whirlpool Refrigerator - Instructions

Ordered the replacement part, came in 2 days, opened the box,rinse and dried it and put in the door. Nothing to it.

Nothing to do, part came, fully assembled, it just went right into the door. Yea!!!

Previously replaced the Fridge light (control board).. The Fridge and Freezer lights were flickering rapidly...LIghts worked fine for four months...then the freezer light went out completely and the fridge light went dim. I unplugged the freezer light and all lights went out! Hooked it back up and ordered new freezer light. After replacing freezer light all three lights work perfectly at full intensity problem solved...For now!

The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

easy peezy - removed old light/module and installed new one works great.

Dismantled the ice bin, and then the ice crusher. I then replaced the auger drum and reversed the dismantle.
I now have crushed ice once again, just like new.
The blow up schematics help isolate the parts needed beautifully. Just like a jobber would expect.
Thanks Guys,

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

Used a screwdriver to pop the catches and unplugged the light from the top of the freezer. Plugged the new light into the wire connector and pushed the assembly back into freezer top. The freezer light and all the refrigerator lights are now bright.

just added new shelf - perfect fit

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

the piece fit perfectly and delivery was within a couple days. very satisfied.

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.