7WF736SDAM14 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from Roanoke, VA
- Parts Used:
- W10822606
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Motor stopped working
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or spin it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT MYERS, FL
- Parts Used:
- W10822606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator seized because of rust
Replaced motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BRENTWOOD, CA
- Parts Used:
- W11209881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper drawer would not slide in/out easily, piece from cross support would fall in way
removed all three drawers. remove shelf glass, remove shelf frame which the glass sat on.
Removed damaged side support, which had two keyhole slots, I pushed up on the rear screw attach point and then forward for front attach point. Piece slid off and I put the new side support on in reverse.
Really well engineered. I just had to clean all the pieces I took out which added to overall time of job but not really.
Removed damaged side support, which had two keyhole slots, I pushed up on the rear screw attach point and then forward for front attach point. Piece slid off and I put the new side support on in reverse.
Really well engineered. I just had to clean all the pieces I took out which added to overall time of job but not really.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from LINDENWOLD, NJ
- Parts Used:
- WPW10688114
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pan door broke
Simply placed on the front
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from MCKINNEY, TX
- Parts Used:
- WPW10688114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Crisper Door
Removed old door. Attached new door to two tabs. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CEDARVILLE, AR
- Parts Used:
- W10346771A, W10311524
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filters needed replaced
I ordered the filters that were needed and received the wrong items. After reordering and then receiving the proper items the installation went very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from ASHLAND CITY, TN
- Parts Used:
- WPW10654844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer
Once I got a part that wasn't broken in transit (took them sending it 3 times for that to happen), it was a breeze. Remove old drawer, take tracks off old drawer and place on new drawer. Put new drawer in fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST UNION, SC
- Parts Used:
- WPW10347093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of ice container auger was broken
Simply pulled out the old unit and installed new per instructions. I was going to order just the part that houses the auger and ice bucket. I was also going to purchase the lesser quality brands at deep discount but after ready the 'challenges' with all of that - spent the money and saved myself the headaches. (and scratched fingers) Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RIDGECREST, CA
- Parts Used:
- W10407212
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Door gasket had deteriorated and needed replacement
Remove torn old gasket.
Starting with bottom slid the gasket retainer under the door retainer lip on bottom. Repeated for top. Slid the retainer under the open side door retainer lip. Then pushed the gasket as much as possible to hing side. The slid the gasket retainer under the door retainer lip.
Starting with bottom slid the gasket retainer under the door retainer lip on bottom. Repeated for top. Slid the retainer under the open side door retainer lip. Then pushed the gasket as much as possible to hing side. The slid the gasket retainer under the door retainer lip.
Was this instruction helpful to you?
Thank you for voting!