WRF757SDEM00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
POS fridge is constantly under repair.
Understood the problem by removing the old dispenser first. That made me realize I also needed the shaft. Went online and matched up all the #’s and the repair went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Orlando, FL
- Parts Used:
- W11168758
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Water was leaking when ice maker or water dispenser was being used.
Looked for the same repair on line by model number. I found it, watched the repair, then used those instructions to complete the repair on my refrigerator. The disassembly and reassembly took longer than actually replacing the part. It now works beautifully with NO leaks.
Was this instruction helpful to you?
Thank you for voting!
The lights were out in the part of the refrigerator and freezer section of refrigerator.
I ussed meter to check the voltage levels and they were fine. I refrence a you video on the refrigerator and foud out that the lights are setup in series like christmas tree lights. If the freezer light is out it will affect the rest of the lights in the refrigerator. I removed the freezer light module and test the light by swapping it with a know working light. the freezer light was the culprit that took the lights out in the side panels and the left side of the refrigerator section. I replaced the freezer light and all the lights now work without issue.
One light and they all go out. So i used one fo lights
One light and they all go out. So i used one fo lights
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orville from Albuquerque, NM
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Changed water filter. Water came out slowly. took off filter and reinstalled water came out good stream. Ice maker is still not working.
Just stood in front of the refrigerator and disconnected the water filter and replaced it with the new one I purchased from by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from ORLANDO, FL
- Parts Used:
- W10407212
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The rigth door does close tight
I ordered a gasket and follow the instructions, such as warm the gasket, to get it in the door using my fingers, but the door did not close titght enough. The problem could be something else. The initial problem is in there
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Tequesta, FL
- Parts Used:
- WPW10347093
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Getting the second part assembled, should have been pre assembled
With a screwdriver and a lot of time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from BOURBONNAIS, IL
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leaking water valve
Removed old, installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
auger motor was not working in ice maker
I watched some of the you tube videos , the repair went well
just followed the directions the repair took less than 30 mins
just followed the directions the repair took less than 30 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from BROADVIEW HTS, OH
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace refrigerator water filter
I followed the instructions in the appliance reference manual, and successfully replaced the water filter in 2 minutes, and reset the water quality indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from OLEAN, NY
- Parts Used:
- W10865826
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water inlet valve leaking
Removed valve, replaced, slight modification needed on water line going into ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT MYERS, FL
- Parts Used:
- W10822606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator seized because of rust
Replaced motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!