WRF767SDEM01 Whirlpool Refrigerator - Instructions

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Took the old one out & replaced it with the new one

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

(1) Unplug the refrigerator
(2) Remove 4 nut driven sheet metal screw to remove access plate in the back.
(3) Remove a clear hard plastic cover. Several electronic boards are held in place with plastic tabs.
(4) The main electronic board is easily recognizable.
(5) Unplug all wire plugs from main board. Don't work about what plug goes where when reinstalling. Each plug is different from the others. It's fool proof.
(6) I wore vinyl gloves when I handled and installed the new board. I did not want any static charge to jump to the board.
(7) Re-install all electrical plugs. Note use minimum force to remove and install these plugs as some are small and fragile.
(8) Before re-installing the hard clear plastic cover make sure all electrical plugs are properly installed.
(9) Follow thru to reverse removal procedure for metal plate.
(10). Plug in the refrigerator.
(11) I purchased a delay receptable to prevent both electrical surges and reduction in electrical voltage.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice with fingers!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I carefully matched the model number to replacement part cross-reference and ordered the Part.
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the female plug from the refrigerator.

A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Easy

Shut power and water off to unit. Removed all shelving. Removed all drawers. Remove freezer door and drawers for cleaning purposes. Remove top panel. Remove ice maker. Thoroughly clean both. Remove air tower and discard. Remove bottom panel that covers Damper Control assembly and evaporator. Remove Styrofoam support and retainer, discard (most likely to crumble once moved). Remove and replace inoperative damper motor. Install new motor with new support and retainer. Re-install "cleaned bottom cover". Install new air tower. Re-install clean ice machine and top cover. Re-install cleaned drawers then shelving. Re-install all cleaned freezer components. Turn on power and water.

Had a hard time getting the refridgerator part of the filter to LET GO. The grooves weren't lined up with the areas meant to pinch. A knife on each side got it to release.
Thanks.
Have a good one.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.