WRF560SFYH03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vincent from THE VILLAGES, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
install ice maker with all parts for refridgerator with no ice cube hardware on it.
I followed the directions and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from MC CUNE, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ice maker
My husband is an appliance man and he did the work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SCOTTSDALE, AZ
- Parts Used:
- WPW10383615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
not freezing
remove inside cover. meit ice collected, remove old part and install new part. about 1 hr.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PRESTON, MD
- Parts Used:
- WPW10383615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer temp could not get above 28*
1st; Remove all shelving
2nd; Phillips screws,= remove bottom cover, and bottom vent
3rd; Sensor is straight up- plug & play (see pic)!
DO NOT MAN-HANDLE.!
4th; Re-install vent & cover 'SLOWLY'.!
Please buy a "Freezer" thermometer. Good freezers work
around (+5* to -10*) even with food.
2nd; Phillips screws,= remove bottom cover, and bottom vent
3rd; Sensor is straight up- plug & play (see pic)!
DO NOT MAN-HANDLE.!
4th; Re-install vent & cover 'SLOWLY'.!
Please buy a "Freezer" thermometer. Good freezers work
around (+5* to -10*) even with food.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BONITA SPGS, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
install ice maker 2 screws wire harness pluged in done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BONITA SPGS, FL
- Parts Used:
- WPW10326335
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Opened the door and accidentally hit the empty door shelf causing it to fall to the floor.
Simply opened the door and replaced the shelf with the new one.
PS
Be sure to order the correct shelf, because although they looked the same initially they’re not.
My unit has different shelves for the right and the left.
Good product and fast ship!!!
PS
Be sure to order the correct shelf, because although they looked the same initially they’re not.
My unit has different shelves for the right and the left.
Good product and fast ship!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from BROADVIEW HTS, OH
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace refrigerator water filter
I followed the instructions in the appliance reference manual, and successfully replaced the water filter in 2 minutes, and reset the water quality indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SALINA, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
3 screws
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from JASPER, TX
- Parts Used:
- WPW10330850
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I just replaced the drip tray on the front.
Took the part out of the box and placed it where it goes. 2 seconds.
Was this instruction helpful to you?
Thank you for voting!