WRT108FZDB02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deravine from New London, CT
- Parts Used:
- WP2254618
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
the part was loos
the repair it good and easy ,vo helper to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debi from Athens, OH
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
main food compartment too warm
Following the info on another post from partselect site: Unplug the main refridgerator line from the outlet. Removed icemaker(didn't have this hooked up to operate), 2 screws and 1 hex nut; removed back panel of freezer wall (interior), be mindful of wiring harness on the left of panel, 2 hex nuts: unplugged fan motor from wiring harness, removed motor with 2 screws, gently, but firmly pulled fan blade off (a little tricky due to housing bracket around it) carefully noting 2 soft rubber gaskets that holds the unit in bracket. replace motor with new one ... follow above steps in reverse. helpful to have a small flashlight. make sure soft rubber gaskets are seated in place. Fan blade requires a firm but gentle push back on the metal post ... bottom of back panel seats over an opening in order for it to fit snug against the wall. I am totally satisfied with the info and seamless, expediant service with partselect ... thank-you so much ..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Brooklyn, NY
- Parts Used:
- 4387478
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Protective cover for bulb had melted
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from grundy, VA
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
frige not cold
i removed the back cover off in the icebox,removed the fan motor,replace the new one now it works fine.very easy to do,saved alot of money on a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lawrenceville, GA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Light switch which turns on the lights when the door opens went out
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L. from Delanson, NY
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
change evap.fan motor
unplugged the fridge removed the shelf, remove the rear wall to access the motor removed the 2 screws holding the motor and unplugged motor from harness, then unplugged the groung wire .then put it back together up and running in 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Skyler from San Marcos, TX
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer running, yet fridge warm.
The fridge went warm and I noticed ice build-up on the freezer floor underneath the coils. I mistakenly thought that the defrost heater (or thermostat or timer) must have been the culprit. I used a voltmeter to test those components and chased a wild goose for quite sometime before realizing that the evaporator fan was not spinning and that it failed a test with the voltmeter. Replacing the fan easily fixed my problem! I later realized that the sheet of ice on the freezer floor indicated that the defrost cycle had been working. Were that not the case, the ice would have been all over the coils.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Jefferson Township, PA
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Light
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Randolph, ME
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Frig not cooling.
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from River Edge, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Fairport, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ba from Van Nuys, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator stop cooling
I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph T. from Morgantown, WV
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this instruction helpful to you?
Thank you for voting!