WRS586FLDW01 Whirlpool Refrigerator - Instructions

Removed the cover to ice maker. Removed with 1/4 inch socket and the extension, the 2 Nutscrews holding the ice unit in place by bending down the plastic cross piece in front of the screws. Finally squeezing the electrical cover case to remove from the rear wall to get to the Electrical plug connection. Once cover away from the wall and new plug connected, the new ice maker was hung onto the upper slots and nut screws re-installed, again by bending the plastic cross piece for ease of securing the unit. Re-installed the cover and turned the unit on - it made ice like when the refrigerator was new.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

Simply cut the water tube on both sides of connector and push in the new one.

ordered new filter, removed old filter from fridge, and installed new one

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.

When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.

NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Unhooked water line from house to fridge then unbolted valve from fridge body then removed plastic water line from fridge to valve by pushing in on pex release tab then reversed process with new valve. Works like a charm. No more leakage. Wood floor is dry and Happy!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door.
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.