WRS322FDAM04 Whirlpool Refrigerator - Instructions

Replacing the broken parts for my Whirlpool refrigerator was very easy and the price was reasonable.

Shut off water supply. Unplug refrigerator. Removed lower back cardboard panel. Removed two screws holding inlet valve bracket to side frame. Pulled valve out far enough to gain access to water lines and electrical connectors. Used 9mm open end wrench to press in collars to remove water lines from inlet valve. Used small container to catch water dripping from lines. Removed defective valve and replaced with new one by first pushing water lines into respective openings, make sure they are fully seated. Reconnected electric wires. Installed inlet valve on side frame. Replaced back panel. Plugged in power cord. Opened water supply. Flushed about 2 gals of water through system. Note: water may not flow immediately due to air in water lines.

remove door pull gasket out put new gasket in replace door

Followed the u tube directions disconnect the power to the refrigerator remove the Ice cube pan place flat head screw driver under the front tabs push in to release the tabs pull down on the light release the back tabs from housing pull the light down from the housing disconnect the plug from the burned-out diode replace with the new diode light and repeat the same instructions in reverse to reinstall the diode light. The diode light in the freezer controls all the light in the refrigerator and freezer all should now light up.

Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had short wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.

Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee

As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.

STRANGE ! to moment I installed the filter ALL the internal lights in my refrigerator went OFF and never came back.

Strange !! refrigerator works fine but no more light in it !!

My email is : Lucfontaine91@yahoo.com

DON'T USE earthlink email anymore

took old bin out replaced with new , two minute job
Parts select is an easy co. to do business with THANKS Andrea

replaced

I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & tightened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.

Ordered the replacement part, came in 2 days, opened the box,rinse and dried it and put in the door. Nothing to it.

i replace the old broken one, very simple and easy,thanks very much for the part, the price was really good better than sears, they were charging me for the same pretty much $100.oo, so thanks for everything, the time frame delivery was excelent!!!!! so i'll be keep you name first on my providers list for my next job......!!!!!!!
sincerely;
wilfredo Uztariz

Hold both water filter reset touch sensors down together. This will reset the water sensor indicator.

Previously replaced the Fridge light (control board).. The Fridge and Freezer lights were flickering rapidly...LIghts worked fine for four months...then the freezer light went out completely and the fridge light went dim. I unplugged the freezer light and all lights went out! Hooked it back up and ordered new freezer light. After replacing freezer light all three lights work perfectly at full intensity problem solved...For now!